LS engine variants part two - Generation IV (2023)

This article was originally published in the 2014 issue ofStreet Machine's LSX Tunermagazine


IN 2005, after eight years, the Gen III made way for the heavily revised, four-inch bore Gen IV-series small-block, again being unveiled in the new sixth-generation Corvette (C6).

Rather than radically re-engineering the platform all over again, Chevrolet evolved the basic architecture to push the displacement as far out as 7011cc (427ci), while also including new technology like fly-by-wire throttles, displacement on demand and variable valve timing.

LS engine variants part two - Generation IV (1)The Gen IV has been one of the most horsepower-rich engine line-ups in GM’s history, featuring race-ready powerplants such as the dry-sumped, 505hp 427-cube LS7 and the king-of-the-hill 638hp (476kW) supercharged 6.2L LS9.


LS family tree part one: Gen III

LS2 - 4.00in BORE

LS engine variants part two - Generation IV (2)Stepping up from the 5.7L, the aluminium LS2 displaces 5967cc (364ci) thanks to a 101.6mm (4.00in) bore and 92mm (3.622in) stroke. It retains the #243-casting cathedral-port heads from the LS6 (without lightweight sodium-filled valves) and, in 2005-2007 Corvette-spec, makes 400hp (300kW), with 2005-2008 E-series HSVs going 12hp better to make 412hp (307kW). Compression was increased over the LS1 (10.25:1) and LS6 (10.5:1) to 10.9:1.

The 2006-2007 Cadillac CTS-V and 2006-2009 Chevrolet Trailblazer SS also got the engine, which was upgraded by using rectangular-port cylinder heads in place of the more restrictive cathedral-port heads.

Values for LS2s have dropped since the introduction of the LS3.


LS engine variants part two - Generation IV (3)


An iron-block Vortec 5300 engine, the LY5 replaced the Gen III LM7 engine in 2007. SUV fitments produce 320hp (239kW) while pick-up truck-fitment engines make 315-320hp (235-239kW).

The LMG is the flexible fuel variant of the otherwise identical LY5. LMG and LY5 engines are found in 2007-on Avalanches and half-tonne Suburbans, among other Chev and GMC models.

After 2010 these engines both scored variable valve timing, though the LMG does not feature AFM.


Introduced in 2006, the L98 and L76 are 6.0-litre variants of the LS2. The L76 was used in February 2006-on VZ and VE (auto only) Holden Commodores, Statesmans and Caprices (WL and WM models).

L98 versions were fitted to VE Series I (and VZ SS Thunder) Holdens equipped with manuals. While the American-market engines scored Displacement On Demand (DOD) technology, it was disabled for Aussie motors, though we did get Active Fuel Management (AFM) on cars with 6L80 automatic gearboxes.

LS engine variants part two - Generation IV (4)


Removing the DOD and AFM from the L76 changed the camshaft, lifters and other minor fittings in the L98’s top end. The square-port cylinder heads flow far better than earlier cathedral-port heads, but this change in design means intake manifolds and most top-end parts don’t interchange between earlier LS engines and the L98/L76.

The introduction of L98 and L76 engines signalled the end of cable throttles for Aussie GM V8s.

Holden L76s produce 260kW, while the auto Pontiac G8 made 269kW. GM also made a truck variant called the Vortec 6000, based on Holden’s L76, to replace the Gen III LQ9.

Found in 2007-2009 Silverados and Sierras, it made 274kW and featured AFM and variable cam phasing.

The L77 debuted in the Series II VE Commodores for both automatic and manual transmission choices. The L77 is the flex-fuel variant of the L76 and produces 270kW.

LS engine variants part two - Generation IV (5)


(Video) Ultimate LS Engine Overview


Want a high-flowing, lightweight 6.0-litre on a budget? Gran an L98. Once a budget pick, word has gotten out about these impressive motors and you'll be paying between $3000* and $6000* for second-hand or crate engines. (*prices quoted as at 2014)


Launched in 2008, the LFA is an all-aluminium Vortec V8 and was fitted to GM hybrid GMT900 trucks and SUVs. The LFA features 10.8:1 compression and makes 332hp (248kW); it was only offered in 2008 and 2009 model years.

A heavy revision of the LFA, the all-aluminium LZ1 truck and SUV motor features upgraded fly-by-wire throttle, new oiling system, AFM and variable valve timing, while still pumping out 332hp (248kW).

It was again offered in 2010-2013 hybrid trucks and SUVs.


The 4.8L Vortec 4800 LY2, first launched in 2007 GMC and Chevy trucks, replaced the Gen III LR4 and is the smallest member of the Gen IV family. The iron-block V8 is also the only Gen IV truck and SUV motor to not feature variable valve timing. It makes between 260-295hp (194-220kW) depending on application.

LS engine variants part two - Generation IV (7)


The Vortec 4800 L20 is an iron-block Gen IV variant of the LY2, but is equipped with VVT on both intake and exhaust. It does not feature AFM and makes 260-302hp (194-225kW).


The LH6 is a Gen IV Vortec 5300 5.3L V8 truck/SUV motor with AFM technology and is the aluminium variant of the LY5.

It produces 315hp (235kW) and can be found in such models as the 2005-2009 TrailBlazer and (we kid you not) Saab 9-7X.

Vortec 5300 300hp (220kW) LH8s were fitted to 2008-2010 H3 Hummer SUVs and 2009-2012 Colorado pick-ups, featuring a different sump layout to suit the GMT345 and GMT355 truck engine bays, but they do not feature AFM.

The Vortec 5300 LC9 is a four-wheel-drive fitment, flexible-fuel-ready Gen IV making between 315hp (235kW, in pick-ups) and 320hp (239kW, in SUVs).

Variable valve timing has also been added to the LH6 and LC9 post-2010.

Note: These engines come with a rear-hump sump, making them excellent prospects for conversion into old Holdens.


The LS4 is a 5328cc (325ci) transverse front-wheel-drive fitment Gen IV V8. Construction is all-aluminium, it has AFM and features #243 cylinder heads as found on the LS6; however there are significant changes over rear-drive engines.

LS engine variants part two - Generation IV (8)


The bellhousing bolt pattern differs and the LS4 crankshaft is shortened 13mm (3mm at the flywheel and 10mm off the front) compared to a 6.0L. Accessories are driven off a single serpentine belt and the water pump is remote-mounted on an elongated manifold that connects it to coolant passages.

The 303hp (226kW) engine is found in the 2005-2008 Pontiac Grand Prix GXP, 2006-2009 Chev Impala and more. The LS4 replaced Cadillac’s overhead-cam, bum-dragger Northstar V8, which was also used in Buicks and Pontiacs.

(Video) GM Gen 3 vs Gen 4 LS Engines...What are the Differences?


With 30 engines across 17 years, there are dozens of seemingly minor variances that can easily catch an unwary engine-swapper out. Here are a few things to consider when shopping for an engine.

There are three main types of sump used on LS motors – rear-hump, front-hump and winged. Gen III-equipped Commodores generally run the front-hump unit, while the VE onwards runs a rear-hump sump. Corvettes tend to use a winged design. Check out page 120 for more sump info.

LS engine variants part two - Generation IV (9)


While all LS engines run top-feed fuel injectors, there are a few minor differences you need to be aware of when swapping across generations and models.

Early Gen III LS1/LS6s and truck motors were fitted with a Minitimer connector on the injector, while the LS2 changed to a USCAR wiring clip.

For the Gen IV a physically shorter top-feed injector was used, but with the same USCAR clip. Flow rates for injectors changed depending on the motor specification; anywhere from 24lb/hr (252cc/min) to 70lb/hr (735cc/min).

The awesome 320cfm Gen IV rectangular-port heads are only a direct fit on 4.00in-and-larger-bore blocks. There are plenty of aftermarket cylinder heads to fit smaller-bore motors, though.

Similarly, as mentioned above, the Gen IV and Gen III crank sensors use a different reluctor and trigger wheel set-up (24-tooth for Gen III, 58-tooth for Gen IV).

There are also roughly six different serpentine belt layouts just across the popular LS engines. These include the truck and Corvette systems, the early F-Body LS1 set-up, CTS-V Cadillac drive system, 2010 LS3 Camaro configuration and blown Corvette set-up.

Finally, in 2004 GM changed from using two different cylinder-head bolt sizes to one uniform size, placing the threads deeper into the block.


In 2006, muscle-car fans and Chev-heads lost their collective marbles when the 427 reappeared in the GM parts catalogue. The 7008cc Gen IV LS motor is a hand-built, all-aluminium engine, but very different to other engines in the line-up.

LS engine variants part two - Generation IV (10)


The cylinders are a Siamese layout, with no water passages in between, so Chevy could punch the cubes out while retaining strength.

The LS7 runs a wild 4.125in bore and 4.00in stroke, while the LS2’s 4.4in bore-spacing is retained. This required pressed-in cylinder sleeves to retain strength.

The forged steel crank and bearing caps, forged titanium conrods and hypereutectic pistons all mean the high-revving NA motor will hang together at high rpm. The LS7 can reach these high revs thanks to gigantic 2.20in (56mm) Del West titanium intake valves and huge 1.61in (41mm) sodium-filled exhaust valves, while the rocker ratio has been increased to 1.8:1 from the LS3’s 1.7:1.

LS engine variants part two - Generation IV (11)


Power is officially rated at 505hp (377kW), though some claim crate motors will easily spin to over 550hp on engine dynos, while GM testing reputedly saw them pull to 8000rpm.

Along with the track-oriented 2006-2013 C6 Z06 Corvette, the LS7 has been fitted to a wide range of vehicles, including the 2008 HSV W427, helicopters and boats.

LS engine variants part two - Generation IV (12)


(Video) SDPC Tech Tips: Gen 3 and Gen 4 LS Engine


Tuners have found big gains from fitting an angrier cam, tune and higher-flowing injectors to LS7s, with up to 30 per cent more power available.


Based on the LS3, the supercharged LS9 is the most powerful engine ever offered by GM in a regular production model. The 6162cc (376ci) block is the same as the LS3, as the LS7’s 7.0L (427ci) block was deemed too fragile to withstand the cylinder pressure of forced induction.

LS engine variants part two - Generation IV (13)


Equipped with dished hypereutectic 9.1:1-compression pistons and high-strength conrods, the centrepiece of the engine is the Eaton four-lobe HTV2300 (2.3L) supercharger.

Only offered in the C6 (2009-2013) Corvette ZR1 and via GM’s crate motor program, the LS9 produces a mighty 638hp (476kW) and 8190Nm.


LS engine variants part two - Generation IV (14)


One issue when swapping LS9 and LSA motors into other cars is the extra height the supercharger adds to the engine. HSV had to lower the front subframe of the F-Gen GTS to fit the LSA in under the bonnet line.


In 2007 the LS2 was replaced by a new 4.06in-bore family, including the 6.2L LS3. They feature variable valve timing and AFM, as well as higher power outputs across the range.

The 2008 Corvette introduced a new entry-level engine that would go on to power most of the factory high-performance GM cars through to today: the LS3.

The bore of the LS3 was increased to 4.06in (103mm) over the LS2 to punch the new motor out to 6162cc (376ci), while the camshaft is a more aggressive 0.551" (14mm) lift unit and compression is up to 10.7:1.

LS engine variants part two - Generation IV (15)


Cylinder heads are rectangular-port castings as found on the L92/L76/L98, with 6mm offset intake rocker arms, 2.165in (55mm) intake valves and 1.59in (40mm) exhaust valves, though the LS3 also scored hollow stem valves that allows it to rev to 6600rpm compared to 6000rpm in the L76. It’s topped off with a higher-flow intake manifold and the same 47lb/hr (493cc/min) injectors from the LS7.

GM paired this tech to a bi-modal exhaust for a 6hp boost to 436hp (325kW). HSV introduced the LS3 in the E1 HSV range, producing 425hp (317kW) before tweaking it up to 436hp (325kW) for the 2009 E2 series and, with the optional bi-modal intake and tube-steel headers, 450hp (340kW) in the Gen-F Clubsport SV.

The LS3 has also been fitted to the 2009 Pontiac G8 (the US-export VE Commodore), and 2013-on Chevrolet SS (the US-export VF SSV).

LS engine variants part two - Generation IV (16)



Arguably the perfect mix of out-of-the-box performance with cost and ease of fitment, the LS3 is fast becoming the number-one choice for pro-tourer builds.

(Video) LS Engine Swap - Generation Identification - Summit Racing Quick Flicks


LS engine variants part two - Generation IV (17)


A lower-performance variant of the LS3, the L99 is fitted with AFM and variable valve timing, as found in the Camaro SS. It produces 400hp (300kW), redlines to 6000rpm (not 6600rpm like the LS3) and features a different valvetrain to suit the AFM variable displacement.


From 2007 the Cadillac Escalade has featured the new Vortec 6200 L92, a 6.2L (379ci) all-aluminium V8. Featuring two-stage VVT, it produces 403hp (301kW). In 2009 the L92 was modified for flex-fuel capability and renamed the L9H, and then again as L94 when AFM technology was added in 2010.


LS engine variants part two - Generation IV (18)


The supercharged 6.2L LSA is a lower-performance variant of the LS9 and debuted in the second-generation Cadillac CTS-V (2009).

It has a smaller supercharger (1.9L vs. 2.3L), lower compression ratio (9.0:1 vs. 9.1:1) and smaller intercooler and cast pistons, while some early (Cadillac) LSAs also missed out on the LS9’s piston oil squirters. Originally making 556hp, it was bumped up to 580hp for the Camaro ZL1 (2012) and HSV’s Gen-F GTS (2013).

LS engine variants part two - Generation IV (19)


The LSA is the most powerful LS engine variant sold new in Australia.


One reason we didn’t see the LS9 fitted to the HSV is that General Motors have an internal edict not to allow any car to be more powerful or faster than the top-line Corvette.

Iain Kelly


Iain (or Marv, as he’s known on the internet) has worked in automotive journalism since 2002, when he was Street Machine’s work experience kid.

General Motors


Street Machine Archives

(Video) All 5 Generations Explained. Plus Every Engine Ever. (Updated for 2022)



What year did LS go to Gen 4? ›

Roughly in 2003, GM upgraded the LS into its Gen IV configuration with a number of changes. The upgrades included a 58x crank trigger wheel with the cam sensor moved to the timing chain cover. The LS was eventually delivered in multiple cubic inch configurations that did not stray far from its ancestral roots.

What engines are Gen 4 LS? ›

LS Gen IV Engine Overview

The Gen IV family began with the LS2 and includes LS7, LS3, LS9, and L92.

Are Gen 3 and Gen 4 LS parts interchangeable? ›

Even though most parts can interchange on LS Based engines, it is important to know the differences between a Generation 3 and Generation 4 LS engine. There are many things that are different between these two generations of engines and can really be difficult to decipher what parts you need for your build.

Is the LS2 a gen4? ›

The 6.0 liter V8 LS2 engine was produced by General Motors for use in performance vehicles and sports cars. It is part of GM's Gen IV Small Block engine family and was first introduced in the 2005 Chevrolet Corvette C6, Chevrolet SSR and the Pontiac GTO.

What is the difference between LQ9 and Gen 4? ›

The ONLY difference between an LQ4 and LQ9 is the piston!

The LQ4 piston is dished where as the LQ9 is a flat-top increasing compression to 10:1, and HP to 345 factory. The LQ9 is a limited production engine and VERY desirable as it is the HO 6.0L and comes with a premium price.

How much horsepower does a Gen 4 LS engine have? ›

Gen 4 versions of the 4.8/5.3L engines did see a slight increase in horsepower and torque numbers because of improvements in combustion ratios and better fuel mileage in their factory trims, netting around 300hp/320tq.

What did a Gen 4 5.3 come in? ›

Here are just some of the vehicles the 5.3 Vortec can be found in: 2007–2013 GMC Sierra 1500. 2007–2014 GMC Yukon XL 1/2 ton. 2005–2008 Pontiac Grand Prix GXP.

Is LQ4 Gen 3 or Gen 4? ›

The LQ4 is a 6.0L LS (Gen. 3) small block engine used in GM trucks between 1999 and 2007. For marketing purposes, it was also known as the Vortec 6000.

What Gen is a 5.3 LS? ›

The 5.3L LS, or Vortec 5300, is primarily a truck/SUV engine that spanned both the Gen. III and Gen. IV versions of the GM LS lifespan. It's essentially a longer-stroke version of the 4.8L LS and powered vehicles such as the Silverado, Sierra, Yukon, and Escalade.

What year did Gen 3 LS come out? ›

Generation III (1997–2007)

Is the LM7 a Gen 3? ›

The LM7 is a 5.3L, Gen. 3 small block engine used in GM trucks between 1999 and 2007. For marketing purposes, it was also known as the Vortec 5300. The information listed here is for the stock LM7 engine.

What is the difference between LS2 and LS3? ›

While the LS2 has a bore of 101.6mm, the LS3 has 103.25mm. Not only does this help with providing the additional 30 horsepower gained with the LS3 (or 36hp with the HSV variants,) but it also makes the engine more rev-happy at the same time.

What is better Gen 3 or Gen 4? ›

PCIe Gen 4 doubles the data rate of PCIe Gen 3, allowing PCIe Gen 4 devices to transfer data at much faster speeds. PCIe Gen 3 operates at 8 GT/s (gigatransfers per second) which roughly translates to 1 GB/s per PCIe lane.

Are 4.8 and 5.3 cranks the same? ›

The 4.8L flat-top pistons are a common (and inexpensive) upgrade for a 5.3L. Crankshaft and connecting-rod casting numbers are the real key to distinguishing between the two. If you have crank casting numbers ending in 216 and rods ending in 143, then you have a 5.3.

Will Gen 3 heads fit Gen 4? ›

If you want to use a Gen III block with a Gen IV computer, you can use these same bosses for the Gen IV knock sensors. The Gen III valley cover looks quite a bit different because it houses the knock sensors (removed from this engine already, along with the rubber gaskets that seal it).

Are LS2 and L98 the same? ›


Introduced in 2006, the L98 and L76 are 6.0-litre variants of the LS2. The L76 was used in February 2006-on VZ and VE (auto only) Holden Commodores, Statesmans and Caprices (WL and WM models). L98 versions were fitted to VE Series I (and VZ SS Thunder) Holdens equipped with manuals.

Is L76 the same as LS2? ›

The L76 was an adapted version of the LS2. It used new rectangle port cylinder heads. It was also upgraded with Active Fuel Management (AFM) . The L76 was available in the Pontiac G8 GT from 2007-09.

What generation is a LS2 engine? ›

The LS2 is a Gen. 4, 6.0L, aluminum small block engine.

What's better LQ4 or LQ9? ›

The LQ9 was an improved, high-output version of the LQ4. It was introduced in 2002 for the Cadillac Escalade. It was available in the Escalade and GM pickups until 2007. The LQ9 was also known as the Vortec HO 6000 or the VortecMAX.

Is LQ9 Gen 3 or Gen 4? ›

The LQ9 is a 6.0L Gen. 3 small block engine used in GM trucks between 2002 and 2007.

How much HP does a 6.0 LQ9 make? ›

LS Family: Gen. 3, 6.0L, Iron Block, Truck Engines
Performance Specifications
Compression Ratio10.1:1
Horsepower Rating345 hp
Torque Rating380 ft./lbs.
Jun 1, 2017

What is the most powerful stock LS engine? ›

The ZR1 wasn't just the sportiest version of the Corvette, but this vehicle was also the most powerful car General Motors ever made until then. The LS9 engine made 638 HP at 6,500 RPM and 604 lb-ft of torque at 3,800 RPM.

What is the most powerful LS? ›

LS9: The Most Powerful LS to Date Thanks to Boost

More power was derived from the roto-cast cylinder heads and a 2.3 liter Roots-type supercharger. Like the LS7, it was a dry-sump engine and was hand built at the Wixom Performance Build Center.

What is the biggest factory LS engine? ›

Biggest LS Crate Engines
  • BluePrint 625 hp/427 cu-in LS Retrofit Crate Engine.
  • Chevrolet Performance 627 hp LSX 454 Crate Engine.
  • Chevrolet Performance 650 hp/6.2-liter LT4 Crate Engine.
  • Boost District 750 hp LSX376-B15 LS Crate Engine Package.
  • Prestige Motorsports 800+hp Supercharged 427 cu-in LS Next Crate Engine.
Dec 22, 2021

What year did 5.3 go Gen 4? ›

Gen. IV LS & Vortec Engine Quick Reference Guide
Generation IVLiterReluctor
20 more rows
Apr 5, 2018

What does LS4 mean? ›

The LS4 engine is a Gen. 4, 5.3L, aluminum small block engine used in GM cars between 2005 and 2009. It is unique because it was the only LS engine used in FWD vehicles. The LS4 had cathedral port cylinder heads and used Active Fuel Management (AFM).

How much horsepower does a 5.3 LS4 have? ›

303 hp. 323 ft./lbs. 5.3L / 325 c.i.d.

Is LQ9 a Gen 4? ›

Intro to the LQ4 and LQ9 Engines

The LQ4 and LQ9 are Gen. III, 6.0L, iron block, truck engines.

How much horsepower does a 6.0 LQ4 have? ›

300-330 hp

How much HP can a stock LQ4 handle? ›

The stock rods will handle about 700 hp. and 6,500 rpm. This is plenty of power for most people. However, if you plan on using boost or nitrous, get Forged Connecting Rods.

When did Gen 5 5.3 come out? ›

Generation Five (2013-Present)

The Ecotec3 5.3 is a combination of all the Vortec tech advancements all rolled into one neat package. It features variable valve timing, Active Fuel Management and brings the addition of direct injection to the plate.

Is LS6 a Gen 3? ›

The 5.7L LS6 is the most powerful Gen. 3 small block engine as it came from the factory. It is an improved version of the LS1 produced for the 2001 Z06 Corvette. The LS6 powered the 2001-04 Corvette Z06 and the 2004-05 Cadillac CTS-V.

What is the difference between LM7 and L59? ›

The L59 was introduced in 2002. It was the flex fuel version of the LM7. This meant it could run E85 and gasoline. The L59 was available in GM pickups and SUVs until 2007.

How many LS versions are there? ›

LS1, LSX, LSA, LS2, LS9 – there are around 40 different flavours of LS engine ranging from 255hp 4.8-litre donks right through to 650+hp 6.2-litre powerhouses – and that's without even considering the aftermarket options. LS9 vs LSA: What's the difference?

What Gen is a 6.2 LS? ›

LS Family = Gen. 4, 6.2L, Aluminum Block, Car Engines
Other Specifications
Intake ManifoldCar-Style
Fuel Injector Flow42 lb./hr. @ 58 psi
Flex Fuel Capable (E-85)No
Fuel Injector Length (between O-rings)1.500 in.
10 more rows
Sep 13, 2017

What is the difference between LM4 and LM7? ›

The LM4 is a 5.3L, Gen. 3 small block engine used in GM trucks between 2003 and 2005. It's is very similar to the LM7, except that it's built on an aluminum block, and the LM7 is an iron-block engine. For marketing purposes, the LM4—like the LM7—was also known as the Vortec 5300.

What year is a Gen 3 5.3 motor? ›

GM Gen 3-5 Engine Chart
Gen III/IV/VYears OfferedSize (L)
35 more rows

What is the difference between an LM7 and LS1? ›

The LM7 cam offered more low-speed torque (by as much as 22 lb-ft) up to 4,400 rpm, but the LS1 cam pulled away thereafter. Such is the effect of extra duration, as the LM7 cam was designed to build torque in the 5.3L.

What is the highest HP of LS2? ›

The LS2 engine block has a 4.000-inch bore diameter. The cylinders can be bored to 4.030 inches. However, we recommend leaving them as thick as possible when running boost. The block can handle 850 horsepower.

What does LS stand for in LS2? ›

LS stands for Luxury Sport. Over time, though, the relevance of its original meaning has become less important, and LS has become known as the base model for many Chevy vehicles.

What is LSX engine? ›

The LSX series of crate engines are based on the LSX Bowtie Block and use a number of production-based and LSX high-performance parts to deliver ultimate performance engines that were never offered in production vehicles.

What Gen is the LS4? ›

The LS4 engine is a Gen. 4, 5.3L, aluminum small block engine used in GM cars between 2005 and 2009. It is unique because it was the only LS engine used in FWD vehicles. The LS4 had cathedral port cylinder heads and used Active Fuel Management (AFM).

What's the difference between a 5.3 Vortec and 5.3 LS? ›

Engines with the LS designation were typically set up for passenger car duty while the Vortec line was for GM's SUV and truck lines. In other words, the difference is in the marketing and where the various engines were going to be used across the GM brands.

How do I know if my 6.0 is LQ4 or LQ9? ›

The ONLY difference between an LQ4 and LQ9 is the piston! There are NO embossed or etched exterior markings on the block or heads to indicate one over the other. There is a paper sticker applied to the back of the drivers-side head at time of manufacture that indicates the type of engine.

What car came with a LS4? ›

The LS4 is unique in the LS engine family because it was a transverse-mounted engine used only in front-wheel drive (FWD) cars from 2005-09, namely the Pontiac Grand Prix GXP, the Chevy Monte Carlo SS and Impala SS, and the Buick LaCrosse Super.

How much HP can a LS4 make? ›

The FWD driveline can really only handle about 400 hp. Even upgrading those components to make more power will result in issues with the steering and handling of the car.

How much HP does a LS4 have? ›

Dubbed the LS4, the front-drive version of the LS V8 displaced 5.3 liters, but unlike the 5.3 liter V8 used in GM trucks it featured an aluminum block along with cylinder heads shared with the LS6. It made 303 horsepower and 323 pound feet of torque.


1. Josh's Car Corner - Ep. 79 - Rebuilding a Gen IV LS Engine (Part 2)
(Josh's Car Corner)
2. LS Gen IV Engines, How To Build Max Power Book Review, Is It Worth The Money?
(Goat Rope Garage)
3. All The LS Engines Explained
(337 SPEED)
4. A Quick Guide to the LS in Australia
(Boost Gumps)
5. Difference between the Gen III and Gen IV LS rod
(Muscle Car Solutions)
6. Motown II LS Part 2 - Dyno Test
(Power + Performance)


Top Articles
Latest Posts
Article information

Author: Horacio Brakus JD

Last Updated: 21/06/2023

Views: 6533

Rating: 4 / 5 (51 voted)

Reviews: 90% of readers found this page helpful

Author information

Name: Horacio Brakus JD

Birthday: 1999-08-21

Address: Apt. 524 43384 Minnie Prairie, South Edda, MA 62804

Phone: +5931039998219

Job: Sales Strategist

Hobby: Sculling, Kitesurfing, Orienteering, Painting, Computer programming, Creative writing, Scuba diving

Introduction: My name is Horacio Brakus JD, I am a lively, splendid, jolly, vivacious, vast, cheerful, agreeable person who loves writing and wants to share my knowledge and understanding with you.